Safety Bands
Safety Bands
Description
Safety Bands
- BSC ERL High-conductivity rubber safety band Width 30mm. Height 86mm. + Anti-wind lip
- BSC ERES High-conductivity rubber safety band Width 28.5mm. Height 35mm.
- BSC EA Aluminum profile for BSC ERES / BSC ERL/GOM
- BSC E90 Angular device kit for BSC ERES
- BSC EL70 Device kit for BSC ERL
- BSC EL Linear device kit for BSC ERES
- BES + BRS Transmitter + receiver KIT
- With panels prepared for RESISTIVE BANDS BSC ERL, BSC ERES, they can be connected directly.
- With old or conventional panels, we must use the BSC SC security circuit.
- For remote response (sliding gates) use BES + BRS transmitter + receiver KIT
- ALU-AP Aluminum bar for anti-pinch rubber.
- GO-AP 25cm anti-pinch rubber.
- BCM-B Band with built-in micro for SWING OR TILTING. Approved. Supplied fully assembled. Direct connection to any EMFA panel, connecting it to the closing safety contact. Height: 70mm. Width: 35mm. Length: 2000mm
- BCM-C Band with built-in micro for SLIDING. Approved. With transmitter + Receiver. Supplied fully assembled. Height: 70mm. Width: 35mm. Length: 2000mm.
- BSP (40 X 6mm, 50 X 6mm, 60 X 6mm) “DANGER” signaling band. Supplied in rolls of 10 meters.
- BSC-SC Safety card for band application (WITHOUT BOX) In most of our panels, it is not necessary. (CONSULT)
- OPTIC-R Low-consumption optical emitter for cable band 1 meter.
- OPTIC-E Low-consumption optical receiver for cable band 10.5 meters.
- GOM-L GP12/11-30 rubber profile, stop 1.113 794. Height: 48mm. Width: 20mm.
- GOM-SL Height: 35mm. Width: 20mm.
- CAOPT LAD 2 with interface for rolling doors. Use with OPTIC R for connection. Use with direct OPTIC E (without transmitter-receiver). Required for OPTIC series connection.
- FOTOBOT 2-piece set. NPN. Small-sized photoelectric.
contact band
band contact card BSC SC
Safety Bands
- BSC ERL High-conductive rubber safety band. Width 30mm. Height 86mm. + Anti-wind lip
- BSC ERES High-conductive rubber safety band. Width 28.5mm. Height 35mm.
- BSC EA Aluminum profile for BSC ERES / BSC ERL/GOM
- BSC E90 Angular device kit for BSC ERES
- BSC EL70 Device kit for BSC ERL
- BSC EL Linear device kit for BSC ERES
- BES + BRS Emitter + Receiver kit
- With squares prepared for BANDS RESISTANT BSC ERL, BSC ERES, they can be connected directly.
- With old or conventional boxes we must use the BSC SC security circuit
- For remote response (sliding gates) use Emitter + Receiver kit BES + BRS
- ALU-AP Aluminum bar for anti-pinch rubber.
- GO-AP Anti-pinch rubber 25cm.
- BCM-B Contact band with built-in micro for SWING OR TILTING. Approved. Supplied fully
- assembled. Direct connection with any EMFA board, connecting it to the closing safety contact.
- Height: 70mm. Width: 35mm. Length: 2000mm
- BCM-C Band with built-in micro for SLIDING. Approved. With emitter + Receiver. Supplied fully assembled
- Height: 70mm. Width: 35mm. Length: 2000mm.
- BSP (40 X 6mm, 50 X 6mm, 60 X 6mm) “DANGER” signaling band. Supplied in rolls of 10 Meters
- BSC-SC Safety card for band application (WITHOUT BOX) In most of our boards, it is not necessary. (CONSULT)
- OPTIC-R Low consumption optical emitter for cable band 1 m.
- OPTIC-E Low consumption optical receiver for cable band 10.5 m.
- GOM-L GP12/11-30 rubber profile, stop 1.113 794. Height: 48mm. Width: 20mm.
- GOM-SL Height: 35mm. Width: 20mm.
- CAOPT LAD 2 with interface for roller doors.
- Use with OPTIC R in case of connection
- Use with OPTIC E direct (without emitter-receiver)
- Necessary to connect OPTIC series
- FOTOBOT Set of 2 pieces. NPN. Small size photoelectric.
Safety Bands
- BSC ERL High-conductive rubber safety band. Width 30mm. Height 86mm. + Anti-wind lip
- BSC ERES High-conductive rubber safety band. Width 28.5mm. Height 35mm.
- …